G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through April 25, 2007 » S triple clamp on a R « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Wolfridgerider
Posted on Tuesday, April 24, 2007 - 03:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
I just talked to Xbullet and the S clamp is in the mail for my R. I want to get it turned around as quick as I can so New12r can have my clamp for his bike.

Does anyone know what parts I am going to need to get this done in a timely manner?

I know I need to pick up a set of bars,grips and top clamp. But, will the brake line, throttle cables and wires need to be a little longer. Or will I be able to re-route them?
Top of pagePrevious messageNext messageBottom of page Link to this message

New12r
Posted on Tuesday, April 24, 2007 - 03:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Wires should fit, You will need throttle cables, brake line and clutch cable.

I dont know what you are going to do with the key switch tho?
Top of pagePrevious messageNext messageBottom of page Link to this message

Tq_freak
Posted on Tuesday, April 24, 2007 - 03:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Wolf, I just did the reverse and put an R triple on my S so i can give some insite. The front brake line on the S is longer then the R. Wasn't a problem for me I Just have extra line but you will need a longer one. I think you will also need the S clutch cable, I cant remember if they are different Lengths or if the R just has the Metal Bend at the end of it.

Im not sure if your throttle cables will be long enough, again I had a little extra but I just re-routed them to take up the slack and not bind.
Top of pagePrevious messageNext messageBottom of page Link to this message

New12r
Posted on Tuesday, April 24, 2007 - 03:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Lemme know what you want for the throttle cables and brake line, I have a clutch cable already.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tq_freak
Posted on Tuesday, April 24, 2007 - 03:40 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
New12r - Jinx you owe me a coke.

Good point about the key switch, I forgot about that.
Top of pagePrevious messageNext messageBottom of page Link to this message

Wolfridgerider
Posted on Tuesday, April 24, 2007 - 04:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
P-Clamp should hold the key......I think!
Top of pagePrevious messageNext messageBottom of page Link to this message

Xbob
Posted on Tuesday, April 24, 2007 - 09:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
ive got a xb12sc. i switched to a xbr triple. didnt change the clutch or throttle cable. been fine so far.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bake
Posted on Tuesday, April 24, 2007 - 11:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
You using S bars?
Top of pagePrevious messageNext messageBottom of page Link to this message

Wolfridgerider
Posted on Tuesday, April 24, 2007 - 11:34 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
I don't think so. I am going to the local bike shop and pick up what looks and feels right.
Top of pagePrevious messageNext messageBottom of page Link to this message

New12r
Posted on Wednesday, April 25, 2007 - 06:58 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Going from and S TO AN R IS fine, the cables are longer on an s to they will fit on the R. Now when you go 3 inches further from where they used to go the R cables WILL NOT FIT on an S setup.

Now if you use really low bars(like drag bars or Azionic lows) on the S clamp you MAY?? get them to fit but with anything close to a stock bar setup you can forget it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bake
Posted on Wednesday, April 25, 2007 - 08:12 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
The new bars will have to be drilled for the nubs (locators) on the switch housings, or cut the nubs off.
Top of pagePrevious messageNext messageBottom of page Link to this message

Svo1023
Posted on Wednesday, April 25, 2007 - 08:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
should be an interesting situation with the ignition switch....keep us posted how that works out...
mike
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration