Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dago
![](http://www.badweatherbikers.com/buell/messages/thumbnails/68336.jpg)
| Posted on Sunday, February 13, 2005 - 11:32 am: |
|
I'm about to install a new clutch cable, but have one question that I couldn't find the answer to in the archives: Is it safe to remove the bolt that secures the metal clasp that secures the clutch cable to the right-hand side of the tie bar assembly? I'm concerned that if i remove that bolt, the engine may fall a bit. does the tie bar assembly support the weight of the engine? (Message edited by dago on February 13, 2005) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Glitch
![](http://www.badweatherbikers.com/buell/messages/thumbnails/20487.jpg)
| Posted on Sunday, February 13, 2005 - 11:40 am: |
|
It'll be OK. Nothing will happen. Looks familiar?
![](http://www.badweatherbikers.com/buell/messages/37/97140.jpg) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dago
![](http://www.badweatherbikers.com/buell/messages/thumbnails/68336.jpg)
| Posted on Sunday, February 13, 2005 - 11:44 am: |
|
Thanks Glitch. That top triple looks Badd-A$$! Nice call on painting it. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Glitch
![](http://www.badweatherbikers.com/buell/messages/thumbnails/20487.jpg)
| Posted on Sunday, February 13, 2005 - 11:48 am: |
|
Thanks, still getting used to how different everything is, but so far I like it a lot. How much shorter is the R clutch cable? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dago
![](http://www.badweatherbikers.com/buell/messages/thumbnails/68336.jpg)
| Posted on Sunday, February 13, 2005 - 12:59 pm: |
|
I'm not sure. It's hard to say now that the new one is on. But I'd say a 2-4 inches? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Roc
![](http://www.badweatherbikers.com/buell/messages/thumbnails/18518.jpg)
| Posted on Sunday, February 13, 2005 - 03:28 pm: |
|
Take care screwing the cable into the primary cover, it is easy to over tighten and break. |
|