Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Steveford
| Posted on Saturday, July 16, 2016 - 06:42 am: |
|
I have to swap out a piston so am looking for the Harlee circlip removal/installation tool. Thanks Steve Ford Pennsylvania |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Ebutch
| Posted on Saturday, July 16, 2016 - 09:23 pm: |
|
Make one pipe has to be larger dia than wrist pin----- www.badweatherbikers.com/buell/messages/3842/25842.html?1074988565
![](http://www.badweatherbikers.com/buell/messages/21/789808.jpg) Now Back to my Ride !!!!! Or use larger deep scocket. (Message edited by ebutch on July 16, 2016) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Steveford
| Posted on Sunday, July 17, 2016 - 06:00 am: |
|
It's the tool for removing/installing the circlip I'm after, not the pin. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Phelan
| Posted on Sunday, July 17, 2016 - 01:35 pm: |
|
Just get very intimate with a small flat head screwdriver. That's how I remove and install XL circlips. Twin Cam circlips are way worse. (Message edited by phelan on July 17, 2016) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Buelliedan
| Posted on Monday, July 18, 2016 - 12:30 pm: |
|
As Phelan said, you do not need a special tool. A small screwdriver will easily get them out and you can out the new ones in by hand. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Hughlysses
| Posted on Monday, July 18, 2016 - 12:42 pm: |
|
Just make sure you stuff rags in the crankcase cylinder openings before you start so one doesn't find its way into the bottom end accidentally. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Steveford
| Posted on Tuesday, July 19, 2016 - 07:22 pm: |
|
Okay, I'll give it a shot and see how it goes. I'll get this old pile back on the road yet! |
|