Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dennis_c
| Posted on Friday, January 16, 2015 - 07:41 pm: |
|
I know this is the wrong place does any one have a good sprage clutch,the gear it runs on,crank shaft nut, gasket? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Nobuell
| Posted on Saturday, January 17, 2015 - 10:34 am: |
|
I just replaced all of that for my replacement. I purchased all on line from Surdyke on line. Had the best pricing. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dennis_c
| Posted on Saturday, January 17, 2015 - 04:10 pm: |
|
Nobuell thanks I will give them a try |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Stevel
| Posted on Saturday, January 17, 2015 - 05:32 pm: |
|
Here is a thought. I'm pretty sure neither Rotax nor HD made that sprague. There is a very good chance the spague can be purchased from a bearing supply house for a lot less money. It's worth the research. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dennis_c
| Posted on Saturday, January 17, 2015 - 06:29 pm: |
|
I will give that a try there is one about a mile from my house that's where I get all my wheel bearings thanks |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Nobuell
| Posted on Sunday, January 18, 2015 - 09:44 pm: |
|
Just be aware that you will most likely need to replace the starter gear with the sprag and the sprag housing. My gear had indications of brinelling on the interface surface. I had a short write up on the my local clubs face book page: https://www.facebook.com/groups/117011071644461/ |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dennis_c
| Posted on Monday, January 19, 2015 - 02:14 pm: |
|
All 3 are bad housing for sprag clutch,sprag clutch and gear. I wander if the housing has to be smooth like the gear has to be? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Nobuell
| Posted on Monday, January 19, 2015 - 10:10 pm: |
|
I replaced the housing but did not check the inside surface. I assumed if the inner was damaged the outer would be as well. Not worth the chance to me. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dennis_c
| Posted on Saturday, January 31, 2015 - 09:12 pm: |
|
Nobuell I took a dermal with a drum sander sanded the rough part of the gear and the sprag housing and smooth them up new sprag clutch works great. That saved me over $200 I will have to see what happens in the long run. Thanks for the tip on Surdyke HD that saved me about $60 over my local HD and got the parts in 10 days. I went about a 60 mile ride today before the snow hits. tonight Total parts $248![](http://www.badweatherbikers.com/buell/clipart/beer2.gif) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Nobuell
| Posted on Sunday, February 01, 2015 - 10:50 am: |
|
Hopefully the drum sanding works for you. I am afraid the new sprag my be damaged. It is a precision ground bearing surface. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dennis_c
| Posted on Monday, February 02, 2015 - 11:55 am: |
|
are you saying I do not have precision hand sanding? ![](http://www.badweatherbikers.com/buell/clipart/selfgrenade.gif) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Nobuell
| Posted on Monday, February 02, 2015 - 06:48 pm: |
|
Perhaps you have a much steadier hand than I do. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Nobuell
| Posted on Wednesday, February 18, 2015 - 03:57 pm: |
|
I was finally able to start my track bike for the first time after the new sprag installation. Sounds great again. |