G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Author Message   Methyman Posted on Sunday, August 14, 2011 - 05:24 pm:        I have a like new CR belt with less then 300 miles on the belt, used 76 tooth CR sprocket and custom aluminum over sized pulley to set the correct tension on the belt with bearing installed. I would like $350.00 shipped in the lower 48 states. The bike has more useable power for the street but I don't like the higher rpm on the highway with this gearing swap. Belt is $182 retail plus shipping Custom Pulley $220 shipped Rear sprocket $140 retail plus shipping   Methyman Posted on Sunday, August 14, 2011 - 05:45 pm:          Methyman Posted on Saturday, August 20, 2011 - 05:44 pm:        Someone must need this?   Andymnelson Posted on Saturday, August 20, 2011 - 11:34 pm:        Wouldn't the oversized front pulley negate the point of an oversized rear pulley??   Methyman Posted on Sunday, August 21, 2011 - 03:58 am:        No! Using the stock 1125R swing arm you need the over sized pulley due to the longer belt and to keep the tension correct for the belt.   Andymnelson Posted on Monday, August 22, 2011 - 11:09 am:        I realize that, but the benefit of going to the CR gearing is the ratio is steaper. If the both pulleys are larger, then the ration is likely not changed or changed very little. So I'm curious, what is the benefit?   Northernyankee Posted on Monday, August 22, 2011 - 11:30 am:        The front pulley is not a drive pulley it is a tension pulley to keep the belt tight.   Andymnelson Posted on Monday, August 22, 2011 - 12:39 pm:        Well now that makes sense! Knowing that, I have a buddy that needs this I'll send him a link to this thread.   Xywh Posted on Monday, August 22, 2011 - 04:45 pm:        OK - I'm Andy's friend that "needs" this. In truth - yes, I've wanted to gear my 1125R to the CR for quite some time. I prefer the gearing, but actually liked the front of the R better. At any rate - I'm fairly sure I'd have to reprogram my ECM for this as well?   Dmfb88 Posted on Monday, August 22, 2011 - 05:18 pm:        Xywh, I would agree that you would too. Or just deal with a speedo that is off. Or buy a cr race ecm from eebr   Xywh Posted on Monday, August 22, 2011 - 05:22 pm:        Dmfb: I'd do that if I hadn't JUST bought the 1125R Erik Buell Racing ECM tuned for the Barkers Exhaust   Methyman Posted on Monday, August 22, 2011 - 05:57 pm:        You can send back to Erik Buell Racing and reprogram it for $35. This is a copy of a email I got from Erik Buell Racing when I inquired about it. It will have to be re-programmed if you want the speedo right. The cost is $35. Send ECM along with instructions of what you want it programmed for, along with a check for $35 to: Erik Buell Racing LLC 2799 Buell Drive, Unit C East Troy, WI 53120 Attention: Recalibration   Methyman Posted on Monday, August 22, 2011 - 05:58 pm:        That cost includes shipping back as well. Later Matthew   Dmfb88 Posted on Monday, August 22, 2011 - 09:41 pm:        What methyman said.

Add Your Message Here Post: -Color- Black Red Green Blue Yellow Purple Orange Cyan Gray White -Font- Arial Courier Symbol Times Verdana -Size- Smallest (-2) Small (-1) Normal Large (+1) Largest (+2) Username: Posting Information: This is a private posting area. Only registered users and custodians may post messages here. Password: Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.) Enable HTML code in message Automatically activate URLs in message Action: