Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jayz
| Posted on Friday, August 20, 2010 - 06:02 am: |
|
Hi all, I've just installed E.B.R ECM (fuel pump + barkers) and when i get into diag mode, i found these errors: - TPS SYS ERR - FUELPMP SYS ERR - FUEL PR SYS ERR - IAC SYS ERR - TIPOVER SYS ERR - ACT INT SYS ERR - IAT SYS ERROR - RT FAN SYS ERR I haven't ridden the bike yet but have run it and let it idle for 10 mins and it seems fine. Has anyone else experienced this? Should i be worried? Look forward to your responses... |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jules
| Posted on Friday, August 20, 2010 - 06:11 am: |
|
That's normal, Erik Buell Racing don't normally have the time to reset all of the historic codes before shipping. They'll go away after 50 cycles. If you get a new "genuine" fault the EM light will stay on. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jayz
| Posted on Friday, August 20, 2010 - 06:38 am: |
|
Thanks Jules. phew! Would turning the key on and off considered a cycle or do i have to actually start the bike? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Mountainstorm
| Posted on Friday, August 20, 2010 - 07:51 am: |
|
Have to start it and let it warm up. I would not worry about the codes at all. They will erase on their own and will cause no issues. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jayz
| Posted on Friday, August 20, 2010 - 08:21 am: |
|
Thanks mate. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Milleniumx1
| Posted on Friday, August 20, 2010 - 12:04 pm: |
|
Same when I installed mine, but I was expecting it (based on posts here) so it didn't alarm me. I never had any new 'real' ones occur, and they all cleared after 50 cycles. I wasn't counting them exactly, but 50 seems about right ... Mike |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Froggy
| Posted on Friday, August 20, 2010 - 12:17 pm: |
|
Same thing happens when you get your stock ECM updated at the dealer, but usually they clear them out since they are already connected. ![: )](http://www.badweatherbikers.com/buell/clipart/happy.gif) |
|