Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
B00stzx3
| Posted on Sunday, April 11, 2010 - 03:48 am: |
|
Well finally got done the open airbox mod and breather reroute with the Lowe's catchcan. Bike runs a like a champ..when in neutral. Revs up and everything. Took it for a spin and bike dies when clutch is released. I mean engine, lights everything. As soon as I pull clutch back in lights come back on and so does engine. I been searching the knowledge vault and figure it might be the sidestand wiring or something? Cuz it runs fine in neutral. Maybe I bumped/disconnected something when routing the breather? Also put the exhaust back on after packing as well and wrapped oil lines in heat shielding. Maybe I bumped something down there? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Glitch
| Posted on Sunday, April 11, 2010 - 07:22 am: |
|
Side stand safety switch, I'd bet |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
B00stzx3
| Posted on Sunday, April 11, 2010 - 12:08 pm: |
|
Aitey, thanks Glitch. I'mma check the service manual. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Froggy
| Posted on Sunday, April 11, 2010 - 12:13 pm: |
|
Yea 03's have that sidestand switch which likes to fail at the worst possible time! ![: )](http://www.badweatherbikers.com/buell/clipart/happy.gif) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
B00stzx3
| Posted on Sunday, April 11, 2010 - 12:26 pm: |
|
haha I'm just now seeing the recall! Couldn't be a worse time your right..its sunday, nice weather and all my shifts are done. SHould I remove the switch altogether? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Glitch
| Posted on Sunday, April 11, 2010 - 12:29 pm: |
|
I by-passed mine. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
B00stzx3
| Posted on Sunday, April 11, 2010 - 12:34 pm: |
|
OK cool, thanks guys. Found this via search- Loose1 "Bypass the the switch. You just need to connect the two wires. A female spade connector does the trick. Stick it in the plug coming from your ecm, by the switch. Also I do the clutch switch. Mine went bad and it would shut off the ecm while I was ridding. Matt" Gonna try this out. THANKS!!!!! |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
B00stzx3
| Posted on Sunday, April 11, 2010 - 02:07 pm: |
|
Clip got disconnected. Must've bumped it or something when we were reattaching bottom fairing or when we put exhaust and cathcan in. Thanks all |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Greg_e
| Posted on Sunday, April 11, 2010 - 02:26 pm: |
|
What size is that spade connector? Might make a good thing to have for emergency repairs. Toss one of those in the "tool" kit. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Terrys1980
| Posted on Sunday, April 11, 2010 - 02:51 pm: |
|
Most likely 1/4" |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
B00stzx3
| Posted on Sunday, April 11, 2010 - 02:57 pm: |
|
Good idea Greg. Yeah I dunno what size, we just reconnected the clip, zip tied and eletrical taped. Ghetto rig haha. But will have something more stable done later tonight. Sweet baby jeebus I love the Buell community! |