G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Bike dies after clutch released w/open air and breather « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

B00stzx3
Posted on Sunday, April 11, 2010 - 03:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Well finally got done the open airbox mod and breather reroute with the Lowe's catchcan. Bike runs a like a champ..when in neutral. Revs up and everything. Took it for a spin and bike dies when clutch is released. I mean engine, lights everything. As soon as I pull clutch back in lights come back on and so does engine. I been searching the knowledge vault and figure it might be the sidestand wiring or something? Cuz it runs fine in neutral. Maybe I bumped/disconnected something when routing the breather?

Also put the exhaust back on after packing as well and wrapped oil lines in heat shielding. Maybe I bumped something down there?
Top of pagePrevious messageNext messageBottom of page Link to this message

Glitch
Posted on Sunday, April 11, 2010 - 07:22 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Side stand safety switch, I'd bet
Top of pagePrevious messageNext messageBottom of page Link to this message

B00stzx3
Posted on Sunday, April 11, 2010 - 12:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Aitey, thanks Glitch. I'mma check the service manual.
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Sunday, April 11, 2010 - 12:13 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Yea 03's have that sidestand switch which likes to fail at the worst possible time! : )
Top of pagePrevious messageNext messageBottom of page Link to this message

B00stzx3
Posted on Sunday, April 11, 2010 - 12:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

haha I'm just now seeing the recall! Couldn't be a worse time your right..its sunday, nice weather and all my shifts are done. SHould I remove the switch altogether?
Top of pagePrevious messageNext messageBottom of page Link to this message

Glitch
Posted on Sunday, April 11, 2010 - 12:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I by-passed mine.
Top of pagePrevious messageNext messageBottom of page Link to this message

B00stzx3
Posted on Sunday, April 11, 2010 - 12:34 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

OK cool, thanks guys. Found this via search-

Loose1 "Bypass the the switch. You just need to connect the two wires. A female spade connector does the trick. Stick it in the plug coming from your ecm, by the switch. Also I do the clutch switch. Mine went bad and it would shut off the ecm while I was ridding.
Matt"

Gonna try this out. THANKS!!!!!
Top of pagePrevious messageNext messageBottom of page Link to this message

B00stzx3
Posted on Sunday, April 11, 2010 - 02:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Clip got disconnected. Must've bumped it or something when we were reattaching bottom fairing or when we put exhaust and cathcan in. Thanks all
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Sunday, April 11, 2010 - 02:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

What size is that spade connector? Might make a good thing to have for emergency repairs. Toss one of those in the "tool" kit.
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Sunday, April 11, 2010 - 02:51 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Most likely 1/4"
Top of pagePrevious messageNext messageBottom of page Link to this message

B00stzx3
Posted on Sunday, April 11, 2010 - 02:57 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Good idea Greg. Yeah I dunno what size, we just reconnected the clip, zip tied and eletrical taped. Ghetto rig haha. But will have something more stable done later tonight.

Sweet baby jeebus I love the Buell community!
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration