Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jschwartz
| Posted on Friday, April 09, 2010 - 10:56 pm: |
|
Couldnt find it by searching, how do I reset the TPS on a 09XB12? (Message edited by jschwartz on April 09, 2010) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
T9r
| Posted on Friday, April 09, 2010 - 11:10 pm: |
|
09s no longer need a TPS reset, whit the newer air cooled engine that was done away with. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Froggy
| Posted on Friday, April 09, 2010 - 11:19 pm: |
|
I guess you didn't read your service manuals. Also, it was posted in several threads in the last few days
quote:To reset an 08+ Buell, do the following: 1. Turn on the key. 2. Set the kill switch to the run position. 3. Don't start the engine. Rotate the throttle from fully closed (gently forced closed) to fully open (gently held open), and then back again to closed (gently forced closed). 4. Repeat 3 times. Hold each position (fully open, fully closed) for 1 full second. 5. Turn the key off and on.
|
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Roysbuell
| Posted on Saturday, April 10, 2010 - 12:13 am: |
|
Would there be any reason to do the tps reset if you don't have any problems and have made no mods? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Froggy
| Posted on Saturday, April 10, 2010 - 12:17 am: |
|
Not really. One of the tuners does it before every dyno run to insure consistent results, but it is overkill for normal people. You should only have to do it if you swap the ECM or you are troubleshooting a running issue. Hell, it takes only a minute to do, so doing it whenever you remember can't hurt. ![: )](http://www.badweatherbikers.com/buell/clipart/happy.gif) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jschwartz
| Posted on Saturday, April 10, 2010 - 07:33 pm: |
|
I installed the Jardine GP1 and EB Racing ECU. CK engine light is on. I'll try this. Thanks |
|