G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Author Message   Scdobber Posted on Monday, January 18, 2010 - 01:36 pm:        Do the Cyclones have factory set rev limiters? Just in case of a missed shift ect.... (Message edited by scdobber on January 18, 2010)   Kilroy Posted on Monday, January 18, 2010 - 01:42 pm:        Yes   Scdobber Posted on Monday, January 18, 2010 - 02:09 pm:        Any idea on the rpm? Thx   Kilroy Posted on Monday, January 18, 2010 - 02:23 pm:        I think its 6800 stock - Someone with better memory than mine will chime in if I'm off Do you have a service manual? Kilroy   Buellistic Posted on Monday, January 18, 2010 - 02:39 pm:        BUELLers: OEM is 6500 RPM ... IMHO, is the max. RPM to shift at on the EVO SPORTSTER Engine is 6800 RPM ... If you want your rods to last, stay below 6500 RPM ... "MAY THE LONG LASTING BUELL BE WITH YOU !!!"   Scdobber Posted on Monday, January 18, 2010 - 02:59 pm:        The reason I asked is I somehow missed a shift from 3-4 and had it rev up to about 6300 for a split second but didn't hear the limiter,I must not be shifting up high enough   Blake Posted on Monday, January 18, 2010 - 04:51 pm:        Since 1996, the Buell tube framer rev limits were all 6,800 rpm.   Outdoors Posted on Monday, January 18, 2010 - 06:24 pm:        The stock ignition begins to retard the timing, I believe @ 6500 rpm and eases up to the 6800 rpm limit. The Buell race ignition goes hard until it cuts out at 6800 rpm.   Blake Posted on Tuesday, January 19, 2010 - 12:28 pm:        Ignition timing on the S1's, M2's, S3's, and X1's is slightly retarded beginning at 6,200 rpm compared to the race module. It's not that big of a difference though, a couple degrees or so is all if I recall correctly.   Blake Posted on Tuesday, January 19, 2010 - 12:34 pm:        More info and dyno testing of stock versus race modules... http://www.badweatherbikers.com/buell/messages/384 2/10398.html?1059591514   Renamed Posted on Thursday, January 21, 2010 - 09:27 am:        "Since 1996, the Buell tube framer rev limits were all 6,800 rpm." Blake you are wrong.   Richsm2 Posted on Thursday, January 21, 2010 - 11:27 am:        "Since 1996, the Buell tube framer rev limits were all 6,800 rpm." Blake you are wrong. Then make it right. I have for 9years ,without I guess any documentation thought it was 5700,Ineed a tach.   Jayvee Posted on Thursday, January 21, 2010 - 12:16 pm:        In any case, the original question was answered, the missed shift caused no damage whatsoever.   Richsm2 Posted on Thursday, January 21, 2010 - 12:21 pm:        I blew the float valve out of position and got gas all over my garage.   Blake Posted on Thursday, January 21, 2010 - 03:57 pm:        I did forget that the S2 was produced as a 1996 model. Its rev limit was lower at 6,200 rpm as it was a stock Sportster engine.   Buellistic Posted on Thursday, January 21, 2010 - 06:45 pm:        Blake: IMHO, a stock SPORTSTER will rev to 6800 RPM with no problem with a 7000 RPM REV limiter Module ... My 1958 XL (iron head SPORTSTER) would, which was before LIMITERS !!! "i" REV'ed it 8000 RPM by mistake and the rods broke ...

Add Your Message Here Post: -Color- Black Red Green Blue Yellow Purple Orange Cyan Gray White -Font- Arial Courier Symbol Times Verdana -Size- Smallest (-2) Small (-1) Normal Large (+1) Largest (+2) Username: Posting Information: This is a private posting area. Only registered users and custodians may post messages here. Password: Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.) Enable HTML code in message Automatically activate URLs in message Action: