G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through October 10, 2009 » AFR and ECM Spy « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Kdogshirow
Posted on Tuesday, September 29, 2009 - 05:24 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Does ECM Spy have the ability to show the Air Fuel Ratio ? Max & Min. settings ? If it does , I am not looking in the correct page or menu , because I can't find any AFR #s . Or can I only get the AFR reading on a Dyno ? I know its not the same as the AFV #s . Thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Swordsman
Posted on Wednesday, September 30, 2009 - 10:13 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Don't think so, because the bike doesn't monitor A/F. The ECM only reacts to a high or low voltage coming out of the O2 sensor, and adds or subtracts fuel depending on if the readout was above or below its target voltage setting. ECMSpy does show those target values, but there's nothing that spells out what the actual A/F ratio is.

~SM
Top of pagePrevious messageNext messageBottom of page Link to this message

Kdogshirow
Posted on Wednesday, September 30, 2009 - 10:57 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Where are those target values located in ECM Spy Swordsman ?
Top of pagePrevious messageNext messageBottom of page Link to this message

Swordsman
Posted on Wednesday, September 30, 2009 - 11:41 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Ummmmmm.... dang, I KNEW you were gonna ask that! I can't remember which tab it is, but there will be a small box area on the right hand side with three voltages listed vertically. Seems like the box is actually labeled something about the O2. I think it may be under the "Other Maps" tab.

I'm at work right now, or I'd pull it up and see...

~SM
Top of pagePrevious messageNext messageBottom of page Link to this message

Patagonia_101
Posted on Wednesday, September 30, 2009 - 02:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

pic
Top of pagePrevious messageNext messageBottom of page Link to this message

Swordsman
Posted on Wednesday, September 30, 2009 - 04:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Aha! That's what I'm talkin' about! FYI, you'll need to have ECMSpy set in "Advanced" mode, or "Expert" mode, or whatever they call it, to see that tab. It's in the settings.

~SM
Top of pagePrevious messageNext messageBottom of page Link to this message

Krueger08xb12s
Posted on Thursday, October 01, 2009 - 08:24 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
so i can't use this awesome software on my 08Xb?? None of it??
Top of pagePrevious messageNext messageBottom of page Link to this message

Bartimus
Posted on Thursday, October 01, 2009 - 08:51 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
NOPE!
The ECMspy software does not work with the DDFI-3 on the '08 and up models. : (
Top of pagePrevious messageNext messageBottom of page Link to this message

Buelltastic
Posted on Thursday, October 01, 2009 - 11:13 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
If I have the factory race kit, what could I stand to gain by getting ecm spy and learning how to use it?
Top of pagePrevious messageNext messageBottom of page Link to this message

Scotty_j
Posted on Friday, October 02, 2009 - 08:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
Well, with ECM Spy, a laptop, and a cable you can datalog and tune your bike to the gnat's ass, perform your own AFV & TPS resets, check and clear trouble codes, and (if you're not careful) you could brick your ECM.

Do LOTS of reading and proceed with caution.
Top of pagePrevious messageNext messageBottom of page Link to this message

Cthagreekgod
Posted on Friday, October 02, 2009 - 09:26 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
I just got ECM spy myself. The guy who sold me the wire also gave me all of the maps (stock and race maps since2003). If I load the race map onto my stock ECU, will it be exactly the same as the race ECU that I already have? If so, Race ECU for sale! :-)
Top of pagePrevious messageNext messageBottom of page Link to this message

Kdogshirow
Posted on Friday, October 02, 2009 - 08:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)
If someone needs a Ecm DDFI-2 , I have one of my 07 XB9R to sell . This will work with ECM Spy . PM me .
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration