Author |
Message |
Sleez
| Posted on Friday, May 01, 2009 - 05:41 pm: |
|
can anyone help cross these p/ns with current p/ns? i bought these in a lot years ago, and don't know what they all are. 2898Y, hex head bolt, 3/8-16x1 7/16 (45) 3104Y, screw, 5/16-18x7/8 (2) 2862Y, flat head cap screw, 1/4-20x13/16 (27) 2878Y, Mach hex head cap screw, zinc 5/8-18x11/16 (2) i think these are isolator bolts? 3241Y, screw, 5/16-18x4, black button head (3) 3202Y, flat top screw (8) 2861Y, SHCS, 1/4-20x13/16 (1) 3502Y, Button HCS, 1/4-24x3/8 (5) 2857Y, Button HCS, 1/4-20x11/16 (5) 2584Y, Bolt, S1 (20) 2847Y, washer (8) 2886Y, Button HCS, 5/16-18x1 7/16 (3) 2875Y, SHCS, 5/16-18x15/16 (3) 2855Y or YA? 1/4-20x7/16 SHCS (1) thanks in advance. |
Brinnutz
| Posted on Saturday, May 02, 2009 - 12:32 pm: |
|
Get your parts manuals out guys and look at the hardware listings in the back...it's listed in numerical order! This stuff isn't in the 02 M2 parts manual...I'm guessing it's from 95-97 Buell's. |
Scarecrow
| Posted on Saturday, May 02, 2009 - 01:51 pm: |
|
This is all I got out of a 2000-2001 X1 Lightning parts catalog; 3104Y Pg.53-Screw that holds the passenger peg mounting bracket to frame. 2878Y Pg.57-Isolator screw the attaches swingarm to mounting block. 3202Y Pg.71-Self-taping screws that hold the fuel cap flange and boot together (and maybe into fuel tank?!?). 2857Y Pg.83-X1 dash mounting screw That's all I found in my catalog. (Message edited by scarecrow on May 02, 2009) |
Sleez
| Posted on Saturday, May 02, 2009 - 03:14 pm: |
|
scarecrow, thanks |
Easy_rider
| Posted on Saturday, May 02, 2009 - 05:31 pm: |
|
There are a couple that are S2 numbers, with one in between that isn't. I'll spend some time later crossing what I can find. |
Easy_rider
| Posted on Sunday, May 03, 2009 - 01:04 am: |
|
This was a little disconcerting. Seeing these made me realize how much my S2 I didn't disassemble. All the parts are probably in a box, but may not be in the condition I'd like. If you're selling, I'm interested!! 2898Y , hex head bolt, 3/8-16x1 7/16 45.00, S2 & S3 Front frame to helm joint, S3 Footpeg to footrest mount 3104Y screw 5/16-18x7/8 2.00, not found 2862Y, flat head cap screw, 1/4-20x13/16, 27.00, S2 Rotor to the front brake carrier 2878Y, Mach hex head cap screw zinc 5/8-18x11/16, 2.00, S3 Rear Isolator bolt 3241Y, screw 5/16-18x4 black button head, 3.00, not found 3202Y, flat top screw, 8.00, S3 Gas cap trim ring screw 2861Y, SHCS 1/4-20x13/16, 1.00, S2 & S3 Top of the shifter to the shift rod end , S3 Voltage Regulator Mounting bracket - right, S3 Holds rubber pad to kickstand , S2 Bottom of the brake pedal to the shift rod end 3502Y Button HCS 1/4-24x3/8 5.00, not found 2857Y Button HCS 1/4-20x11/16 , 5.00, S2 Venturi to the air filter backplate , S3 Voltage Regulator Mounting bracket - left, S2 & S3 Rear brake reservoir to frame 2584Y, Bolt, S1 20.00, not found 2847Y, washer, 8.00, not found 2886Y Button HCS 5/16-18x1 7/16, 3.00. S2 & S3 Rear gas tank mount , S3 Header to frame (bottom) 2875Y, SHCS 5/16-18x15/16, 3.00 2855YA, 1/4-20x7/16 SHCS, 1.00, S2 & S3 front brake line clamp, S3 brake line and clamp to frame, S3 Flasher mounting screw I'm not sure how to insert a table to make this easier to see, but here's a spreadsheet
|
Sleez
| Posted on Sunday, May 03, 2009 - 01:24 am: |
|
roger, thanks a ton! yeah it will all be for sale, just needed to see what the heck i had to start with. i also have 10 needles 27273-96Y and 1 shift link rod, 33805-94Y. don't have much need for any of it, except the few parts i want to send Brinnutz and a few i want to keep just in case. the rest will go cheap. let me know what you need. |
Easy_rider
| Posted on Sunday, May 03, 2009 - 12:39 pm: |
|
If it goes to an S2 or S3, I'm likely to need it. After going through this S2 I'm starting to get the itch to revive the frame in my basement. |
Roaldnelson
| Posted on Sunday, June 14, 2015 - 04:57 pm: |
|
2898Y is one of the bolts used on the tie assemblies. Used in 4 places on S3Ts. |
|