Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Rick_a
| Posted on Tuesday, July 08, 2008 - 12:43 am: |
|
Such a simple little bugger but such a pain to install.
![Zipper's Crank Scraper](http://www.badweatherbikers.com/buell/messages/3842/374407.jpg) My motor build is almost done (new style crank, headwork, etc), but a split locknut on S&S pushrods has halted progress for now.
Note the fancy engine stand. Eventually it'll be back in here
...and it'll look something like this:
![](http://i164.photobucket.com/albums/u40/Ricky_a_photos/IMG_0359.jpg) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Puddlepirate
| Posted on Tuesday, July 08, 2008 - 06:38 am: |
|
What are the specs on your motor? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Rick_a
| Posted on Tuesday, July 08, 2008 - 08:50 am: |
|
Andrews N9 cams, Mikuni 45, Rev-Tech roller rockers, S&S quickie pushrods and lifter travel limiters, Dyna S Dual fire ignition, new '00-up style Buell flywheel assembly, Zipper's windage tray/flywheel scraper, Revolution Performance 1250 kit, Cycle Rama ported XB-style heads, Zipper's Pro Flow oil pump. It made 96RWHP and 82ft-lbs torque before the headwork, so I'm looking forward to finally braking the 100HP mark. (Message edited by Rick_A on July 08, 2008) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Bad_karma
| Posted on Wednesday, July 09, 2008 - 12:51 am: |
|
Nice, looking forward to the end results. Joe |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Puddlepirate
| Posted on Wednesday, July 09, 2008 - 07:38 am: |
|
Sounds like you should definitely be over 100. When do you plan on having it all back together? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Rick_a
| Posted on Wednesday, July 09, 2008 - 11:33 am: |
|
A few days after I get a replacement pushrod locknut she should be rollin'. BTW your Sporty looks tits with that Buell front end. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Bluzm2
| Posted on Wednesday, July 09, 2008 - 03:44 pm: |
|
Rick, I love the "spectator" in the window! |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Rick_a
| Posted on Wednesday, July 09, 2008 - 10:38 pm: |
|
Yes, he likes to follow me around and "help" by smacking my tools against expensive parts. He also points at various components and asks "this?" |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Buell_bert
| Posted on Thursday, July 10, 2008 - 09:31 am: |
|
Curious but what is in the first pic that is a pain to install |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Rick_a
| Posted on Thursday, July 10, 2008 - 02:58 pm: |
|
The setup and clearances. The inner case surfaces are a little irregular and both sides had to be ground to match. Both pieces also had to be trimmed for width. It has to have a .015"-.020" clearance (IIRC) with the flywheel and it's a bit of a trick to get the scraper to keep that clearance once bolted in place. There was a lot of time spent with a grinder and file. There are also no templates or measurements for drilling the holes, and drilling into very expensive parts can be a little nerve racking. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Capndoug
| Posted on Saturday, July 12, 2008 - 02:00 pm: |
|
The guy that will be lapping my pinion warned me not to install a scraper. He has had problems with leaks occurring over time, as the front bolt goes through the outside surface of the case. One instance he said it shifted position and caused some damage. So he only recommends them for race engines. Looks like a nice careful installation though. In addition to the nylon locknuts, I would use thread locker on a vibration intense application like this. Did you thread the holes in the case, or just drilled? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Rick_a
| Posted on Saturday, July 12, 2008 - 02:19 pm: |
|
I did use thread locker, but I did not thread the holes. The thought never occurred to me. That would've been great on those two scraper bolts going through the transmission. I can't see much oil gettin' through there...but I know I will be keeping a close eye on oil levels for some time. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Capndoug
| Posted on Sunday, July 13, 2008 - 07:33 pm: |
|
The installation I was told about the windage tray had fasteners through the front of the case. So, leakage would be much more of a problem than a transmission case hole only. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Hoser
| Posted on Wednesday, July 16, 2008 - 12:11 am: |
|
I've installed quite a few of those zippers scraper kits , It might be a good idea to use washers with captive "o" rings , like on early evo big twin derby covers. To do that , I used 1/4" fasteners on the two bolt locations that enter the transmission area , fluid transfer can occur if you fail to get a god seal here. |
|