Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Slowride
| Posted on Sunday, June 08, 2008 - 07:13 pm: |
|
Show em if you got em! I have a Magellan Maestro 4050 and I am looking for mounting options. As I have the big tank bag and shorter Cityx bars I am trying to figure a good location for the gps. I am a little concerned about road debri impact if mounted outside of the windscreen. Although, I did see an aquabox setup that might eliminate that concern. Anyway, if you got pics of your GPS setup, I would like to see them. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Ft_bstrd
| Posted on Sunday, June 08, 2008 - 07:36 pm: |
|
I have the same unit mounted on a Ram mount and arm attached to the brake reservoir on the right side. I use the arm to mount it low and inboard to prevent crap impact. Remember the Maestro is NOT water proof. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Nevrenuf
| Posted on Sunday, June 08, 2008 - 07:56 pm: |
|
i just got my u-bolt ram mount on the bar right after the clutch lever bracket. i got a tom tom one. at least for me by keeping it on the left side if i have to check anything, i'm not reaching across the tank. as far as road debris goes, it always manages to hit me in the face so i don't worry about the tom tom. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Slowride
| Posted on Sunday, June 08, 2008 - 08:08 pm: |
|
I have seen both of those mounts. I have been looking at the ram mount site for a couple of days now. I like the idea of not reaching across the bike, but the reservoir mount is pretty trick. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Rwven
| Posted on Sunday, June 08, 2008 - 08:23 pm: |
|
Here's my Garmin StreetPilot 2720 (which is waterproof)
![GPS2](http://www.badweatherbikers.com/buell/messages/142838/367329.jpg)
![GPS1](http://www.badweatherbikers.com/buell/messages/142838/367330.jpg)
|
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Ft_bstrd
| Posted on Sunday, June 08, 2008 - 08:48 pm: |
|
Doesn't make that much of a difference between reaching to the center or off center a little. Hasn't been an issue for me. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Maximum
| Posted on Monday, June 09, 2008 - 09:35 am: |
|
Old setup which mounts directly to the Uly crossbar with inexpensive rubber pipe clamp fittings.
![](http://www.badweatherbikers.com/buell/messages/142838/367459.jpg) Current Setup which uses RAM Mount parts attached to the Precision Engineering Top clamp and Pro Taper bars.
![](http://www.badweatherbikers.com/buell/messages/142838/367460.jpg)
|
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Bluethunder
| Posted on Monday, June 09, 2008 - 09:43 am: |
|
![](http://www.badweatherbikers.com/buell/messages/142838/367475.jpg)
|