Author |
Message |
Fresnobuell
| Posted on Wednesday, April 30, 2008 - 06:13 pm: |
|
I found these on the Net. Any recommendations other than one of these two? Or an opinion on which of these two might be more functional or kinder to rims?
|
Hammer71
| Posted on Wednesday, April 30, 2008 - 06:43 pm: |
|
Top one is way better, No Mar products are top notch, work as stated and they stand behind their products. Many here have the No-Mar bar and swear by it. |
Fresnobuell
| Posted on Wednesday, April 30, 2008 - 07:05 pm: |
|
Thanks. I noticed on further inspection that that wilco stuff is just a harbor freight upgrade. I KNOW there is a bar that is made by an "individual" that looked great. I checked his site about a year ago and he was backordered. I sure wish I remember who that was. |
Firebolteric_ma
| Posted on Wednesday, April 30, 2008 - 08:51 pm: |
|
YUP! Hammer knows what works... He showed me the light a year or so ago... No Mar Bar! Yup it works great! All the NEBO guys can attest to it also. I have done a couple dozen tires with that bar... |
Gentleman_jon
| Posted on Wednesday, April 30, 2008 - 09:18 pm: |
|
+1 No mar. |
Ulywife
| Posted on Wednesday, April 30, 2008 - 09:20 pm: |
|
+2 No Mar |
Spatten1
| Posted on Thursday, May 01, 2008 - 12:18 am: |
|
Can you use the No Mar bar without the whole machine? |
Hammer71
| Posted on Thursday, May 01, 2008 - 07:00 am: |
|
Sure can. |
Hogs
| Posted on Thursday, May 01, 2008 - 07:09 am: |
|
anyone have a link on the net for just the bar then? |
Hammer71
| Posted on Thursday, May 01, 2008 - 08:52 am: |
|
http://www.nomartirechanger.com/product/show/6 |
Jimduncan69
| Posted on Thursday, May 01, 2008 - 09:00 am: |
|
hammer, i know you have the bar. but what do you use to hold the tire? |
Hammer71
| Posted on Thursday, May 01, 2008 - 09:19 am: |
|
To take off, Break bead, insert bar and insert small handle thing in the axle hole, stand wheel up on tire and rotate bar, do same for other bead (tire now off). Mounting, Lube tire bead, push tire on and line up balancing marks, second bead wont go on all the way, wood wedge or hold it by hand (firbolteric uses those plastic handi claps), rotate the bar around the bead and boom all done. Will have to video it some day as it's much easier to show someone than to explain it. I will admit though that some tires are so stiff I get a tad pissed off and just spoon them on. Then I go pull the bar out of the wall or ceiling |
Spatten1
| Posted on Thursday, May 01, 2008 - 10:10 am: |
|
What are you guys balancing with? |
Fresnobuell
| Posted on Thursday, May 01, 2008 - 01:26 pm: |
|
What are you guys balancing with? I use a static balancer picked up on ebay for about $70 IIRC. yes, it can take a while, especially if you are anal about stuff. However, you are probably spending MUCH more time than someone else would on your balancing. Plus, a couple more beers isn't bad either. We have done probably 10 balancings with the static balancer with NO problems. |
Chainsaw
| Posted on Thursday, May 01, 2008 - 02:25 pm: |
|
What are you guys balancing with? A pair of jack stands and the bar from the towel rack in my bathroom. Really. |
Spatten1
| Posted on Thursday, May 01, 2008 - 03:06 pm: |
|
Cool, so you just use the axle on jackstands, and the wheel bearing friction is low enough to get the heavy spot to move down? I've always wondered why people don't do that, I assumed the wheel bearings didn't move freely enough. (Message edited by spatten1 on May 01, 2008) |
Ccryder
| Posted on Thursday, May 01, 2008 - 03:26 pm: |
|
That will work but, it may dampen out some of the imbalance, due to the stiction. I've used 5gal plastic pails with some big bearings and the axle. You just need to flush the grease out. It a matter of balance, clearance and, low friction. 90% of the time you could get by without balancing, or you could use those beads (where is Blake when you need an expert ;+}) Neil |
Spatten1
| Posted on Thursday, May 01, 2008 - 03:37 pm: |
|
5gal plastic pails with some big bearings and the axle: Great idea too. I imagine getting the grease out and replacing with a low viscosity lube would work great! This thread rules. |
Chainsaw
| Posted on Thursday, May 01, 2008 - 10:15 pm: |
|
Cool, so you just use the axle on jackstands, and the wheel bearing friction is low enough to get the heavy spot to move down? " Read about the jackstand trick somewhere else. Towel rod was handy and a perfect fit for the wheel bearings. |
|