Author |
Message |
Cyclonemduece
| Posted on Sunday, December 23, 2007 - 01:24 am: |
|
1. What gaskets do i use when i mount this new system to my heads, screamin eagle? 2. The flanges on my stock exhaust look bad does the new system come with new ones? 3. Should i get new studs and install them are there better stainless steel studs? |
Cyclonemduece
| Posted on Thursday, December 27, 2007 - 12:28 am: |
|
what is there 6 of us using this forum? does n e one know? |
Blackm2
| Posted on Thursday, December 27, 2007 - 01:57 am: |
|
The D&D system has new flanges Blake. You have to use the screaming eagles. The stock ones will not allow the headers to seat properly. Depends on the condition of your studs, mine were pretty messed up on the front cylinder and I replaced them. The back cylinder I just put new nuts on. You'll be happy, makes 'em sound the way they were meant to. |
Ratbuell
| Posted on Thursday, December 27, 2007 - 08:36 am: |
|
When tightening the system, slip fit everything from flanges to exhaust tip, but do not tighten a single bolt. Tweak it until it fits without putting any side loads on hangers and header bolts, that's when you know it's straight. Start at the flanges, tighten them to factory spec, and work your way down the system following the exhaust flow. Don't replace the head studs unless you have to. Pulling threads out of the head is a possibility when you remove the studs; I never remove threaded pieces from aluminum unless I absolutely have to. Run a tap down the threads if you have a couple of threads that are boogered, but only replace the studs as a last resort. Following the procedure above will help prevent broken studs down the road. Enjoy the new sound, and don't forget to re-jet! |
Torquemonster
| Posted on Thursday, December 27, 2007 - 06:42 pm: |
|
Got a related question... I bought the D&D for my 00M2, but I dont have the updated front hanger(Y). The muff came with all the hardware and a very large rubber piece that looks as if it would make up for not having the new hanger... Anyone else get this piece in their kit? |
Cyclonemduece
| Posted on Friday, December 28, 2007 - 03:06 am: |
|
??? i have not got mine via UPS but i got the new style hanger from American Sport Bike at the same time. |
Torquemonster
| Posted on Friday, December 28, 2007 - 03:23 pm: |
|
Let me know when it comes in. Looks to me like the big rubber nipple AND the new Y hanger would throw it too far out there..... |
Cyclonemduece
| Posted on Saturday, December 29, 2007 - 01:19 am: |
|
yeah i got it today it said that it was required so i got it i will not be installing it for a while. |
Blackm2
| Posted on Saturday, December 29, 2007 - 10:40 am: |
|
Travis I think that rubber piece must have been for shipping, I have no rubber pieces on my system, anywhere. Definitely need the newer Y-hanger. (Message edited by blackm2 on December 29, 2007) |
Torquemonster
| Posted on Monday, December 31, 2007 - 12:47 am: |
|
Yep....updated hanger on the way. Thanks |
Torquemonster
| Posted on Sunday, January 13, 2008 - 02:41 am: |
|
Dumb question...do I remove the red "condoms" off the muff mount tabs before installation, or should I punch out a hole and slip the bolts through? And...what bracket do I need to secure the rear of the pipe to the bike??? -I recieved NO instructions with my kit. Just a pipe, elbow, clamps, and a couple of nuts and bolts. (Message edited by TORQUEMONSTER on January 13, 2008) |
|