Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Mcintodo
| Posted on Monday, November 02, 2015 - 04:15 pm: |
|
Recently moved from Monterey California to Silverdale Washington. Since I've arrived, the XB12X has been a bit disgruntled. On three separate occasions, the bike would fluctuate in idle, staggering between idle and nearly cutting out. Clutch was fully disengaged, so I hadn't mistakenly loaded the transmission. This morning it happened during the stop and go traffic in the queue to get into work, but raising the rev's of the engine kept it from stalling out. That lasted until I came to a point where the Bike had to be left at idle for about 2 minutes to enter a secured gate. Trying to give the bike power resulted in a back fire, and reportedly about 3 inches of flame out the muffler. The bike stalled out, I cycled the engine cut off switch, and was able to start the bike, though there was a heavy fuel aroma. As a precaution, I rode the bike for 15 more minutes at 30-40 mph to 'clear' things out. I've dived the archive on every permutation of rough, idle, backfire, stall, and move, and done similar through google. The closest thing I have that a possible corrective action is performing a TPS reset (know the procedure), and something about the a learning process for the 09 XB ECM. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Akbuell
| Posted on Monday, November 02, 2015 - 05:28 pm: |
|
Symptoms of being rich/poor combustion. In addition to the TPS reset, I believe there is a procedure in the manual ( which I don't have in front of me - sorry)for the 'cleaning' of the spark plugs. Might want to add that. Or put in fresh ones. If it runs fine otherwise, a nice jaunt on a level road for 25-30mins at steady speed will allow the ECM to learn your new location. If that doesn't work, would be time to check the air filer and inlet, and read up on the Idle Air Control unit and circuit. Hope this helps, Dave |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Mcintodo
| Posted on Monday, November 02, 2015 - 08:03 pm: |
|
Fair enough. I'll try the TPS reset and take it for a go, though finding roads sufficient for a 'level' run will be fun. May just do laps of work. Thanks for the Troubleshooting precedence path. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Akbuell
| Posted on Tuesday, November 03, 2015 - 10:05 am: |
|
Found It ! Had to Google for the procedure, turns out it was a service bulletin for -08 models. May apply to yours. To clear excess fuel re a flooded engine, or to 'clear' fouled plugs, Turn throttle wide open. Set stop/run switch to run. Turn ignition switch on. That should fire the plugs for about 4 sec. Make sure bike is in neutral. There are threads in the knowledge vault about it. I went straight Google. Hope this helps, Dave |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Akbuell
| Posted on Tuesday, November 03, 2015 - 10:14 am: |
|
Also, as to the 'steady speed', the ECM looks at what the engine is doing and what it has been doing for the last little bit. I don't know what the parameters are, but if it 'sees' large TPS changes, and large RPM changes to speed, it decides you are on a twisty road, and refers to the fuel map. If it 'sees' small TPS and RPM changes, it decides you are cruising on a highway, and pays a great deal of attention to the O2 sensor, adjusting the fuel ratio of the entire map, to allow for elevation changes, ect. Hope this helps, Dave |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Mcintodo
| Posted on Thursday, November 05, 2015 - 10:14 am: |
|
Following TPS reset, and about 30 minutes of easy rambling, the back fire issue and staggering during idle has been resolved. Thanks for the Troubleshooting guidance. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Akbuell
| Posted on Thursday, November 05, 2015 - 03:05 pm: |
|
Glad to hear the problem is resolved. And you are very welcome. Dave |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Reepicheep
| Posted on Thursday, November 05, 2015 - 04:55 pm: |
|
Not to jinx it, but if it comes back, look at your cam position sensor for an intermittent failure. |
|