Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jetmech83
| Posted on Wednesday, September 25, 2013 - 02:22 pm: |
|
I have a stock 07 XB9SX with about 18K miles on it. It started to make a rod knock and I took the motor apart and found the rear rod fork bearing was going out. It has a lot of play in it. The local Harley shop said it can't be fixed and I have to buy a new one for around 700 dollars. I looked up Darkhorse Crankworks and saw that they can be remanufactured. I couldn't tell what they charged to have this done. What is the better option? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Hogs
| Posted on Wednesday, September 25, 2013 - 07:27 pm: |
|
I have one I wd. let go for 325.00 plus shipping Its suppose to have only 330 miles on it for a xb9...lmk |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Buelliedan
| Posted on Friday, September 27, 2013 - 11:38 am: |
|
call Dark Horse if you do not get the used one. they are good folks! |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Andersonhdj
| Posted on Friday, September 27, 2013 - 04:29 pm: |
|
I know that XB12 crank failures are being logged and i believe my 05 XB9 was also logged under a separate category. It would be useful to log others as well, out of interest , as it's said that XB9 crank failures are rare. Interestingly there was another failure in East London RSA but don't have any details. In my opinion a Dark Horse rebuild would be money well spent over a second hand crank, no matter what mileage it has on it. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jetmech83
| Posted on Wednesday, October 02, 2013 - 07:21 pm: |
|
I talked to Dark Horse today and they said my crank is probably junk. I leaning towards a new one. I called a buell dealer and they said the assembly part # is 24213-02A. Can anyone confirm this? Also, I am looking the part number for both crank roller bearings. I'm trying to find the best deal on internet. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Andersonhdj
| Posted on Sunday, October 06, 2013 - 05:35 pm: |
|
Did they say why it was "probably junk"? I would.ve thought as long as the webs are intact it would be repairable. Biggest issue being cost! |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jetmech83
| Posted on Thursday, October 10, 2013 - 09:27 pm: |
|
The damaged crank is repairable, but it is cheaper to buy a new one. The machinist at the local Harley shop said my cylinders need to be bore .010" over, but there is no oversize pistons available. So, I need to buy a new cylinder/ piston set. Has anyone had this problem? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Andersonhdj
| Posted on Friday, October 11, 2013 - 11:48 am: |
|
Have you checked for a different brand of piston ? Wiseco or another brand ? Often there are oversizes made by aftermarket suppliers that "Oem" does'nt cover. "Buell" and "cheap" are 2 words that don't occur in the same sentence. Check the classifieds for good usable 2nd hand. Hogs has a crank but i don't know if it is the same as your year model. They did make changes. Even though a D/H crank repair will cost more i suspect it will give you a superior crank than "Oem". |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Reepicheep
| Posted on Friday, October 11, 2013 - 12:12 pm: |
|
Given they would have to be bored out, and then replated with nicisil, it is probably cheaper to buy new jugs (though I don't know how much they cost for sure). I know that for my dirt bikes, it's inevitably $400 plus to rebore / replate, and that's just one cylinder. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Andersonhdj
| Posted on Friday, October 11, 2013 - 01:26 pm: |
|
Reep is right , the nicasil costs an arm and a leg! Post some pics of the jugs n pistons , at 18k they should'nt be worn , perhaps you could get away with a cleanup but can't say without seeing. Interestingly my crank failed at marginally more mileage - 21k, cause unknown. 05 model. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Reepicheep
| Posted on Friday, October 11, 2013 - 01:59 pm: |
|
Watch the used market also. That &*&^^&& Corolla sheared the mount completely off my rear head, and I was able to scare up a replacement (used but clean up and drop in) head for half of what I paid for my last KLR-250 head. Though maybe that was different, as crank problems are likely to kill cylinders and pistons but not heads, and there are a non trivial number of XB12 crank failures. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Andersonhdj
| Posted on Friday, October 11, 2013 - 05:28 pm: |
|
Complete motor?? http://www.badweatherbikers.com/buell/messages/21/ 723370.html?1381520989 |