| Author | Message | ||
     Spiderman |
Oz and Grounskeeper are stuck in Massachsets at Sotherby's or Sheldon's H-D and Buell Alex wasn't sure of the dealers name but was sure that they were stuck in Ma with a bad stator. So if any one in the Ma area could call Oz at 773 895-6504 I am sure it would be apprciated. Thank you, Spidey | ||
| R1DynaSquid |
Got an entire ATC contingent in that area. | ||
| Mikej |
Plus at least three guys on the RAN page. From Buell's site: Sheldon's Harley-Davidson/Buell 914 Southbridge Street Auburn, MA, USA 01501 (508)721-9876 (508)721-0101 (fax) Visit our Web site http://www.sheldons.com Boston Harley-Davidson/Buell 1760 Revere Beach Pky Everett, MA, USA 02149 (617)389-8888/(877)HARLEY-1 (617)387-8871 (fax) Visit our Web site http://www.bostonharley.com Paramount Harley-Davidson/Buell 266-300 Waverly Street Framingham, MA, USA 01702 (508)879-6666 Visit our Web site http://www.paramount-hd.com Kelly's House of Harley-Davidson/Buell, Inc. 1 Chelmsford Road North Billerica, MA, USA 01862 (978)663-6298 (978)663-3480 (fax) Visit our Web site http://www.kellysh-d.com Tibbys Harley-Davidson Sales/Buell, Inc. 227 Berkshire Avenue Springfield, MA, USA 01109 (413)781-0785 (413)781-3215 (fax) Visit our Web site http://www.tibbysharley.com/harley | ||
| Oz666 |
We are at the Auburn Holiday Inn (Auburn, Mass) 508-832-2500 Rm 110 Stator went up in smoke, Sheldon's Harley-Davidson/Buell assures me one will be here tomorrow @ 10 AM... They have the (stator) bolts - no reuse! Looking for a party...  Oz And Grndskpr It was not a doobie... | ||
| Crusty |
I just talked with OZ, and he and Groundskeeper are put up for the night. Oz's bike is safe, and the stator should be at the dealership tomorrow morning at 10:00. The situation is under control, and they have a little "incident" to make the trip a little more memorable. Hopefully, their last leg home will be trouble free, then they can post a ton of pictures from Newfoundland. | ||
| Glitch |
F'n stators, never go out at a good time! | ||
| Grndskpr |
The situation is under control But i am 1000 miles from home and sober?????? and the part will not be in until at the earliest is 10am, soooooooo Whos buying R | ||
| Oz666 |
Before i forget, please let me know if you have these, Torque value for the following bolts: Stator bolts clutch basket and rotor nuts primary allens the job is being completed in the parking lot, by myself and OZ and we dont have a book, and since we are using 5 of there tools, i really would prefer to have the specs handy instead of having to trouble them to much, they have been great but i would prefer to have everything ready to go if i can thanks much R | ||
| R1DynaSquid |
At least you have done the job in the past & can do it blindfolded. See you when you finally get home. | ||
| Grndskpr |
At least you have done the job in the past & can do it blindfolded. Yea but i still need the specs. i have an idea, but Oz says i need to do it right or something like that, as always better safe than sorry Still not fond of doing it in a parking lot but, as always stuff happens, home by Sat, no big deal, FXDX has treated me better than she should have, loads of fun, and some stories i dont think most will belive, i actually was thinking about it last night, and still find it hard to belive more to come(after i get out of this Hotel) R | ||
| Crusty |
From my 1998 S3/S3T service manual: 1) Secure stator using four newTORX screws. Tighten screws to 30-40 in-lbs (3.4-3.5 Nm) 2) (Clutch) Washer must be installed with the word "out" facing the mainshaft nut or transmission may be damaged. Install nut (left-hand threads). Tighten to 70-80 ft-lbs(94.9-108.5 Nm). 3) Tighten Primary cover bolts to 80-110 in-lbs(9.0-12.4 Nm). (Message edited by Crusty on August 11, 2004) | ||
| Awprior |
You'll also need something to wedge between the engine sprocket and the clutch basket when you torque those nuts. Wish I was there to party with ya. It's too long of a ride after the past few weeks, or I'd join you. | ||
| Mr_grumpy |
Here we go Roger, I'm still not back on Euro time so I've been out to the garage in the dark! These are out of the 99/OO Cyclone book, stator mounting screws 30-40 in-lbs, clutch mainshaft nut 70-80 ft-lbs, Engine sprocket nut 190-210 ft-lbs, primary cover bolts 99 models 80-110 in-lbs, 2000 models 100-120 in-lbs. Hope this helps, wish I could come & give you a hand to make Cartman better but you'd be gone before I got there. Say hi to the cook for me, Innes.  | ||
| Buckinfubba |
I've bought the whiskey but I can't find ya....oh well heres to the adventure | ||
| Grndskpr |
2 glasses of screech, going out to dinner i really shouldn't drink on an empty belly wish me luck in the morning, hope the part gets in R | ||
| Newfie_buell |
This is the first time I have checked in since yesterday afternoon. I am back on the West Coast of the island. HOw far is it to Mass, I could always deliver some Screech to help ease the pain and bring more tools. | ||
| Oz666 |
Closer to Buffalo than Sydney - close to Chez Crusty... Thanx for the offer though. I had the forethought to get Screech @ the duty-free (ding-dang good thing, too). Should have new part(s) in under 1 hour. (HAHAHAHAHAHAHAHAHAHAHAHAHAHAHAHAHAHAHAHAHAHAHA) Actually dealer (Sheldon's) has been very helpful. Oz | ||
| Oz666 |
Grndskpr stayed - a big help - I'm not completely around the twist, yet. Oz | ||
| Signguyxb12 |
they are on the road again | ||
| Cj_xb |
YEAH !!!! | ||
| Grndskpr |
made it to Oz's house, a little late, 250 miles in the rain, Mike was a big help(Signguy) off to chicago in the morning, well afternoon everythings cool more to come R |
