Author |
Message |
Dcmortalcoil
| Posted on Friday, June 11, 2010 - 02:45 am: |
|
Anyone experienced in installing stock exhaust? Pretty tough. I thought using a jack on the exhaust will push the exhaust into place. But did not work. Had to resort to rubber mallet to move the exhaust into place. I got all bolt holes aligned after two hours, but can't seem to thread the left front bolt into the loose nut. How are we suppose to tighten the left front bolt - got no room to maneuver or hold the lose nut. Any ideas or suggestions? |
Pdawg1970
| Posted on Friday, June 11, 2010 - 03:56 am: |
|
i dunno about installing, but when i just removed my stock exhaust i managed to get a 13mm box end wrench on the nut on the left side. all the others had nuts 'fixed' to the muffler. i put the left & rite ones up front back in, using nuts on both without any problems. |
Jules
| Posted on Friday, June 11, 2010 - 04:36 am: |
|
There have been a few posts on this topic before, I believe a few people "bent" a spanner of the appropriate size to get it into position. I used a long screwdriver to hold the nut steady when undoing mine but have never had to refit the stock pipe. I did ask a similar question a few months back and there was one response saying it's possible to do the whole job in less than 20 mins.. That one nut is a PITA! |
Jdugger
| Posted on Friday, June 11, 2010 - 08:10 am: |
|
For the nut: Wrap it in safety wire, pull tight, and then bend the length of safety wire so you cna roughly hold it into position while you thread the bolt/nut together. |
D_adams
| Posted on Friday, June 11, 2010 - 08:37 am: |
|
A craftsman open end wrench can be slid up in there with the nut in it, if it keeps falling out of the wrench, tape across the back of the nut and it will hold it in place. You just have to be patient and steady to get it in there, then just gently turn the wrench until the nut rests against the oil cooler bracket. Start threading the bolt into the nut by hand, it will go right in. I've done it numerous times and it's not very difficult. Also, if there's a next time to do this particular job, before you try jamming the pipe back up under the motor, loosen the right side foot peg bracket just a turn or two on the bolts. It makes all the difference in the world in trying to get the pipe back up in place. Mine slides in like it's greased up in warm butter now. Hmmm, that kinda sounded wrong. |
Bigevildoer
| Posted on Friday, June 11, 2010 - 09:44 am: |
|
Don't forget to loosen the right side rear set assembly. If it's tight, you'll never get the stocker back on... |
Avalaugh
| Posted on Friday, June 11, 2010 - 12:31 pm: |
|
2 HRS !!!!!!!!! yours must be a right pain, ill have mine off in 10 mins and back on in 10 mins. Thought it was a great design, hope you get it sorted,after a few times it does get alot easyer i must admit. |
Daggar
| Posted on Friday, June 11, 2010 - 01:26 pm: |
|
Go to the auto parts store and buy a set of wrench ends that will fit on a socket extension. I don't know what they're called but they're just the ends of an open end wrench. You may have to use some tape, as Dean said. |
Jbarron
| Posted on Friday, June 11, 2010 - 02:04 pm: |
|
Did this once and got lucky. I thought a better solution would be to replace the two bolts with one long one. |
Ccryder
| Posted on Friday, June 11, 2010 - 04:19 pm: |
|
Crowsfoot |
Daggar
| Posted on Friday, June 11, 2010 - 04:52 pm: |
|
Woot! Thanks Neil. Couldn't remember what they were called for the life of me. |
Thunderbike
| Posted on Friday, June 11, 2010 - 05:00 pm: |
|
Number one thing is to loosen the shifter and rear brake bracket mounting bolts(no prying or pounding needed).It's way easier to do if you have a lift,but I did one on the ground that did'nt take more than 15 min.to install with ordinary snap-on combi.wrenches.It's tricky but not impossible. |
Dcmortalcoil
| Posted on Friday, June 11, 2010 - 06:16 pm: |
|
Thx much all. I was dead tired and didn't think about loosening the foot peg brackets. That's the tip I needed yesterday. Man what a PITA it was. Thanks to you guys, now I know. It's amazing that the service manual does not mention loosening footpegs. Something simple as that would have saved me time and agony. And who's the nutter that designed the front mount. That left-front nut should have been welded or held like the front-right mount. |
Zac4mac
| Posted on Sunday, June 13, 2010 - 12:28 am: |
|
When the FSM was written, the techs were learning on proto models that had a smaller oil cooler. When I asked Max how he got it off, he said he just stuck a wrench in there. When I got my Drummer, I gave him the 90 degree bent box 13mm I modded. Take a cheap 13mm box-end wrench, heat to cherry red and bend 90 degrees. If it won't hold the nut on re-assembly, put a small piece of black electrical tape in the teeth of the wrench. Zack |
Dcmortalcoil
| Posted on Sunday, June 13, 2010 - 02:16 am: |
|
The front left nut is so illogical. |
Froggy
| Posted on Tuesday, June 15, 2010 - 10:20 am: |
|
I don't know how any of you guys got it in 10 minutes, I am 2 hours in and still can't get anything to line up right, even after loosening the peg bracket. My plan was to throw the stock can back on my R and take it to homecoming, fat chance at this point! |
Therealassmikeg
| Posted on Wednesday, June 16, 2010 - 06:41 am: |
|
Froggy, If you are having trouble lining up the rear muffler mounting holes I would suggest you take a look at the muffler itself. The nuts on the muffler float fore and aft in a slot. You can locate/center the nuts by inserting a pick or small screwdriver through the hole in the foot peg brkt. Leave fasteners loose until you have them all started. Then tighten everything. (Message edited by therealassmikeg on June 16, 2010) |
|