G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through August 18, 2005 » What is trouble code #6 ? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Super8
Posted on Saturday, August 13, 2005 - 12:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)
after 10 meters riding my engine stopped showing 6 flashes on engine light while fan running.
I'm not at home so no service manual, can anyone please help me? No dealers open under 350 km. and all friends so no help around here.
Top of pagePrevious messageNext messageBottom of page Link to this message

Chainsaw
Posted on Saturday, August 13, 2005 - 01:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)
First digit blinks, 2 second pause, then 2nd digit.
Multiple codes blinked after another 2 second pause. If a code repeats, you have them all.

code
11: TPS
13: O2 sensor
14: Engine temp sensor
15: IAT sensor
16: Battery Voltage
23: Front injector
24: Front ignition coil
25: Rear ignition coil
32: rear injector
33: Fuel pump
35: Tach
36: Fan
44: Bank Angle sensor
52,53,54,55: ECM failure
56: Cam sync failure.
Top of pagePrevious messageNext messageBottom of page Link to this message

Daves
Posted on Saturday, August 13, 2005 - 11:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)
See, I told you someone would have the codes for you.
Badweb rocks!
Top of pagePrevious messageNext messageBottom of page Link to this message

Makenzie71
Posted on Sunday, August 14, 2005 - 12:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)
I'd run with the IAT sensor...the others would result in a no-run condition.
Top of pagePrevious messageNext messageBottom of page Link to this message

Opto
Posted on Sunday, August 14, 2005 - 05:03 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)
The CE engine light won't show trouble codes unless you jumper the pins on the ecm data connector. If the CE light flashed in the conditions stated above then it sounds like the motor thinks it's overheated. I would be checking the cyl head temp wire, coming from down inside the centre of the rear cyl. But I've been wrong many times before. Good luck.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bud
Posted on Sunday, August 14, 2005 - 05:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)
reading this http://www.badweatherbikers.com/buell/messages/32777/133279.html?1124011161

i'm with opto,
or your battery is fryed
Top of pagePrevious messageNext messageBottom of page Link to this message

Super8
Posted on Sunday, August 14, 2005 - 12:09 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)
Sorry about it, but I think I made a mistake: I'm running with Power commander (over 2 years) and I assumed being between ecm and engine would protect it from failure; I removed it and now it's only showing an injector failure (maybe a loosen connector), so maybe I was wrong. It's hard to read because in the middle of flashes mostly times fuel pump starts running on/off with blinks on engine light(key switch relay?). Sorry for my ignorance in electrical probs.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration