G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » EBR Forum » RX TPS Reset software and cable question... « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

M1combat
Posted on Saturday, December 05, 2015 - 07:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Will the software and cable for my Firebolt work on an RX?
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Saturday, December 05, 2015 - 07:57 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

TPS is done without software and no it will not work on the RX.

- Turn the ignition on and set the kill switch to the run position - don't start the engine
- Gently force the throttle to fully closed
- Take the throttle to fully open, hold firmly for 1 second.
- Take the trottle back to fully closed and hold 1 second
- Repeat (fully open, fully closed) 3 times
- Turn the ignition off
- Turn the ignition on
- let idle for 10 minutes to relearn
Top of pagePrevious messageNext messageBottom of page Link to this message

M1combat
Posted on Saturday, December 05, 2015 - 08:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Awesome... Thanks Terry : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Skntpig
Posted on Tuesday, December 08, 2015 - 07:37 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

EBR also said you have to wait at least 3 or 4 seconds when the ignition is off before turning it on after the 3 turns. I don't remember exactly but it's in the instructions.
Top of pagePrevious messageNext messageBottom of page Link to this message

1_mike
Posted on Tuesday, December 08, 2015 - 01:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Are these 1125R/CR instructions vs. RX/SX instructions ?

I may have missed them but I see no instructions for the RX/SX TPS reset in the repair manual or the users manual.

I believe, like cars, the software does this on its own..!?

Mike
Top of pagePrevious messageNext messageBottom of page Link to this message

D_adams
Posted on Tuesday, December 08, 2015 - 03:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

1125 = 1190 for TPS reset. Same procedure.
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Tuesday, December 08, 2015 - 03:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The 1190s, just like the 1125s and later XBs will periodically self calibrate so a TPS reset is not needed, but the procedure above is the steps to manually do it. Typically you would only need to do it after swapping the ECM, TPS, throttle body, or similar parts, but even then you likely can get away without doing it.


quote:

- let idle for 10 minutes to relearn




That is not needed for the TPS reset. The bike also self calibrates its idle, so letting it sit for 10 minutes gives it a chance to do that but it also will do it during normal usage.
Top of pagePrevious messageNext messageBottom of page Link to this message

Skntpig
Posted on Thursday, December 10, 2015 - 11:16 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Those instructions were included with the EBR race ecm and tips to r move the secondary muffler.
Top of pagePrevious messageNext messageBottom of page Link to this message

1_mike
Posted on Thursday, December 10, 2015 - 12:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I received no instructions for a TPS adjustment from IDSP after buying their "race" ECM.

I just plugged it in, turned the key, pushed the button. It started and idled fine. Took it out for a short cruze and all was well, been fine ever since.

Pretty similar to Froggys comment.

Mike
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration