G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » Quick Board Archives » Archive through April 26, 2007 » S3 explosion. Help. « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Sooner
Posted on Monday, April 23, 2007 - 11:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I just put together my 98 s3 today, after two years of intending to do it.

The custom paint took longer than I expected.

I installed a forcewinder and also a bracket that allows me to get rid of the breather hoses and use the bracket from d and m motorcycle.

While starting my bike today, the oil plug under the seat flew out, and hot oil went everywhere.

I am just wondering what could cause pressure like that in the oil tank.

I took the seat off, and tried to run it again with the same results. I am at a loss, and any help would be greatly appreciated.

thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Mbsween
Posted on Monday, April 23, 2007 - 11:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Sooner,
You over filled it most likely. The Buell is a dry sump, meaning the oil lives under the seat, not in the bottom of the engine.

So if you check the oil cold, all the oil thats in the engine won't show in the oil level under the seat. Once the beast is running it will pump the oil from the engine back to the reservoir under seat and then you get the problem you 're seeing.

So remember that you can't check the oil unless the bike has been running for awhile. You need to ride it a couple miles for an accurate reading.

Matt
Top of pagePrevious messageNext messageBottom of page Link to this message

Sooner
Posted on Tuesday, April 24, 2007 - 01:01 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Thanks Mbsween, I also have a question about changing to the forcewinder.

I had the carbon fiber race hamcan on before, and It ran great, but I kept jamming my knee on it.

So I changed the breather to the forcewinder, and it fixed the leg room issue, but now it pops and backfires.

I have a new carb jet kit, should I increase the jet size or decrease it to stop this problem?
Top of pagePrevious messageNext messageBottom of page Link to this message

Ezblast
Posted on Tuesday, April 24, 2007 - 01:12 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Carve out you vacuum air intake - you are developing a false lean condition because of it
Email me for a pic and I'll send it to you - old issue, even found in the Thumper section - try search for pic - Forcewinder intake mods -
GT - JBOTDS! EZ
Top of pagePrevious messageNext messageBottom of page Link to this message

Tramp
Posted on Tuesday, April 24, 2007 - 07:16 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

the force is dependent on active intake for optimal performance.
the difference between standing still and moving forward is greatly accentuated with this intake, which means your mixture will vary as a result.
put it on ebay and put a nice, intelligent k&n airbox on it, for consistent airflow.
Top of pagePrevious messageNext messageBottom of page Link to this message

Cereal
Posted on Tuesday, April 24, 2007 - 09:21 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Don't ever run the bike w/out the seat on. That way the cap will never fly off! It did happen to me once too.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration