Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Orngm2
| Posted on Saturday, March 03, 2012 - 01:19 pm: |
|
Replaced the rear isolators on my 1999 X1 yesterday... found a small pin on the floor under the bike. Turns out the LH alignment pin for the rear isolator seems to have sheared off. the orientation of the bolt holes in the islators are the same on each side. do i have anything to worry about? does anyone have a pic showing the new type isolators installed on an X1 on each side? just want to make sure iam ok before i go on. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Orngm2
| Posted on Monday, March 05, 2012 - 07:25 pm: |
|
Thanxs for all the help, i fixed it!! |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Orngm2
| Posted on Monday, March 05, 2012 - 07:26 pm: |
|
PS that was meant to be sarcastic... |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Essmjay
| Posted on Monday, March 05, 2012 - 07:49 pm: |
|
Maybe no one had an answer for you. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dannybuell
| Posted on Monday, March 05, 2012 - 08:44 pm: |
|
How did you fix it? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Orngm2
| Posted on Tuesday, March 06, 2012 - 09:13 am: |
|
The pin was broken off flush... could not get it out of the frame. Installed a smaller but stronger roll pin INSIDE the broken half of the frame. Took the broken pin and slid it over the smaller pina and it fit like a glove. Seems to be stronger too!! |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dannybuell
| Posted on Tuesday, March 06, 2012 - 10:34 am: |
|
Clever! I have always thought of tapping swingarm sub-frame and drilling into the mount and using a small allen bolt. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Natexlh1000
| Posted on Tuesday, March 06, 2012 - 11:22 am: |
|
LOL! Now you have an alignment pin pin. |