G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Motorcycle Forum » Old School Buell » Archives OSB 001 » Archive through February 17, 2006 » Lower engine tie bar----- has touched the oil filter? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Ryker77
Posted on Thursday, January 19, 2006 - 04:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The X1 frame has the extra tube on the lower front tie bar. But I noticed after getting the bike dyno tuned and two short power wheelies on the way home-- the the bolt had touched the oil filter.

I am using the larger ford f1-a1 oil filter--- its a huge ass filter. It would have been a bad day if the oil filter had been punctured-- either caused a wreck or burned up an engine.
Top of pagePrevious messageNext messageBottom of page Link to this message

Leftcoastal
Posted on Thursday, January 19, 2006 - 08:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The term "UNIPLANER" is an old Norwegian term that roughly translates to "F&*# - that motor really moves around a lot in the frame!"
You might want to reverse that bolt, or use a smaller filter!
AL
Top of pagePrevious messageNext messageBottom of page Link to this message

Ryker77
Posted on Thursday, January 19, 2006 - 09:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

or I could just stay out of the thottle and keep the front wheel on the ground..

I'll probably do something to protect that filter.
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Thursday, January 19, 2006 - 09:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Now then don't be rash there!
I suggest you put the normal oil filter back on and continue the wheelies.

Remember to blip the throttle on the way down to reduce the impact.
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Friday, January 20, 2006 - 01:03 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Lefty:
Wes is going after that Scandinavian guy with the turboed busa, who rides wheelies at almost 200 mph [ghost rider]our new bad webb member

"ghost ryker"

Wes: take a peek at the front head steady and iso there bro,

ride safe ............ no just ENJOY!
Top of pagePrevious messageNext messageBottom of page Link to this message

Philip
Posted on Friday, January 20, 2006 - 03:36 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

my m2 hits the big filter unless i put a dent in the filter. i don't feel like the dent hurts the filter at all. better than rubbing a hole in it!

philip
Top of pagePrevious messageNext messageBottom of page Link to this message

Ryker77
Posted on Friday, January 20, 2006 - 09:15 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I am not a wheelie rider. don't think its too safe on the road or at my skill level.

I had just picked the bike up from the dyno shop and was playing with the throotle. When the front wheel came up. Kinda shocked me.

----
so just dent the filter- thats simple enough
Top of pagePrevious messageNext messageBottom of page Link to this message

Dave
Posted on Friday, January 20, 2006 - 10:21 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Part of Tuber Character. That happens to may tuber Buells.... I wouldn't sweat it.

DAve
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration