Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Burckman
| Posted on Friday, June 10, 2011 - 12:16 am: |
|
i installed a new motor and cannot seem to fined the other plug for my nuetral indicator switch can anyone help me with a picture and instructions on where it may be |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Rays
| Posted on Friday, June 10, 2011 - 07:58 am: |
|
The neutral switch is located behind the drive pulley at about 2:30 if you imagine a clock face overlaid on the pulley. The connector on the switch is a single brass pin - this is a picture of the switch so you can recognise the connection:
![](http://img527.imageshack.us/img527/8316/img0282ra0.jpg) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Terrys1980
| Posted on Friday, June 10, 2011 - 09:02 am: |
|
![](http://i40.photobucket.com/albums/e223/TeryS1980/electricalconnections.jpg) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Burckman
| Posted on Monday, June 13, 2011 - 05:20 pm: |
|
yeah thats it i cannot figure out where the other connector is that plugs into the nuetral switch connector |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Terrys1980
| Posted on Monday, June 13, 2011 - 05:40 pm: |
|
It should be right by the ignition and cam sensor connectors. It's just a single wire bullet connector. The switch grounds it to complete a circuit. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Badgerboi21
| Posted on Thursday, May 10, 2012 - 02:17 pm: |
|
I see this is an old thread but recently my neutral indicator stopped working. I believe my neutral switch went bad. I've read quite a few threads regarding the location of the switch but I'm wondering how difficult of a fix this is. I have a 2000 Cyclone. Thanks |