Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Joe_solo
| Posted on Tuesday, July 29, 2008 - 08:15 pm: |
|
07 XB12X - Using ECMSpy to set the TPS. Followed the instructions. Now the bike won't idle. This is what I did! Wound the idle adjust screw till I got 0% and turned it a bit further with the throttle grip twisted closed. Wound the idle screw ti @ 4.6 degrees & 5.1% Then selected "TPS Reset". Can't get the bike to idle. Once started it only runs if the throttle is held. Can anybody tell me what I did wrong? Was I to select "TPS Reset" before adjusting the idle screw to those percents? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Sped214
| Posted on Tuesday, July 29, 2008 - 08:29 pm: |
|
You need to hit "TPS Reset" when the idle's screwed out past 0% and you've made sure the throttle is closed. (Message edited by Sped214 on July 29, 2008) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Joe_solo
| Posted on Tuesday, July 29, 2008 - 08:32 pm: |
|
Thanks Sped214 will try that. Joe |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Marks3tbillet
| Posted on Tuesday, July 29, 2008 - 08:49 pm: |
|
Joe: I had the same problem on my '07. After two attempts, I found that the throttle and idle cable lock nuts were loose and I wasn't really getting the 0%. Make sure cables are adjusted properly and try again. Mark |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Joe_solo
| Posted on Tuesday, July 29, 2008 - 11:28 pm: |
|
Hey Mark & Sped214, Yes, the cable lock nuts were loose. Wasn't following the instructions to a "t". Runs like new now, thanks guys for the help. Joe |
|