| Author | Message | |||
     Xoptimizedrsx |
Posted on Tuesday, May 29, 2012 - 05:20 pm: Edit Post Delete Post View Post/Check IP Print Post Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only) ECM Tuning People, How many people would like a Lite version of the files? This way you only get the base settings like maps, afv, o2 and so on. These will be areas you normally adjust in the ecm VS the full version that we currently have. This would take out all the many tables and scalers you never adjust or need to see in the file. The program will still pull the whole ecm's eeprom and burn it. it just will have a smaller set of layout instructions. This way for new guys learning it you wont be so over powered by all the data. This would alter the XDF only, the ADX you need the full file we have now. Also how many want diag settings to do test and to clear codes? the ddfi2 will get tps reset where the ddfi3 does it by way of the throttle so that does not need to be in it. Regards, Xopti Mike | |||
| Xoptimizedrsx |
This is what I am talking about as a lite version. I still have to remove a couple scalars but you get the point on a lite verse full pro version... This opens to the raw files to show what all goes into a XDF file for those who wonder what the back side of this looks like...
(Message edited by xoptimizedrsx on May 30, 2012) | |||
| Xoptimizedrsx |
I'm setup to make a couple small videos on connecting and setup to use the Tunerpro RT program to read/write and save data. I have to make a bue2d Lite XDF first. I should be recording by Wednesday once I get my test station into the office. Hopefully this helps people whom are stuck or scared of the Program. | |||
| Greg_e |
Yes the lite version and videos would be absolutely welcome! How can someone like me that knows pretty much nothing about the application help? | |||
| Xoptimizedrsx |
You can say its Awesome that I am doing it again... | |||
| Raceautobody |
Yes this would be Awesome. Most owners will only need a lite version. Xopti Thank You for all you have done and are still working on. Al | |||
| Xoptimizedrsx |
This is the lite version of the BUE2D_V5_Lite It is the more simple to use and understand. I am making each version. So far the BUEZD, BUEYD, BUE2D are made. These take about two hours each to build if I dont have a typo and then it will not load if I do... They will post on the Website once done and verified. Free for everyone to get and use...
| |||
| Xoptimizedrsx |
The ddfi2 clear codes, reset tps and run diag is done... Its free on the website... I also have Four Firmwares done on the lite version... 11 more to go... Their is actually 18 total versions but I only support 15 to the public... | |||
| Xoptimizedrsx |
Setup Video... its long but it is what people asked for... http://www.youtube.com/watch?v=5adoPgR98kQ&feature =youtu.be http://www.youtube.com/watch?v=s9nt1_-nrZo&feature=youtu.be (Message edited by xoptimizedrsx on May 31, 2012) | |||
| Xoptimizedrsx |
Some Lite files are now posted online... The ADX files are done for ddfi2 and ddfi3... | |||
| Greg_e |
Thanks for the hard work, going to try and get this working tomorrow. | |||
| Idaho_uly |
Did my first adjustment to the ecm and am very impressed with its around town manners now. Engine is smooth at 2K and 3K rpm. Power like you say is much more linear. But crack the throttle and the Uly pulls very nice!!! Thanks for all your help Mike!!! | |||
| Xoptimizedrsx |
The walk through PDF guide... Its brief but with the video your going to be set... The Guide is here: Using_Tunerpro_RT.pdf | |||
| Jasonb |
Thanks for the great work. I bought a cable off you and never knew what to do with the program. I'm not sure what to Echange and what the changes would do. I feel my bike needs some tweaking since under 2k is a huge vibration and cough zone. I normally cruise at 3-3.5k. I thought was the normal range. Am I incorrect? JB (Message edited by Jasonb on June 05, 2012) |
