| Author |
Message |
    
Hogs
| | Posted on Wednesday, April 20, 2005 - 07:46 pm: | 
|
Hey Norris,
Well just got back from a ride and dark out now so was going to see what the gauge reads now that I can see it guess what, well started bike up and Hmmm gauge reads all 0`s not working will have to check out later I hope its just a wire or its the Worst 175.00 bucks or so I ever blew... |
Norrisperformance
| | Posted on Wednesday, April 20, 2005 - 09:52 pm: |
|
Hogs the Instructions say
You have accidentally hooked the meter
signal wire to the oxygen sensors ground wire,
Maybe thats why you can't see it that good.
(Message edited by norrisperformance on April 20, 2005) |
Hogs
| | Posted on Thursday, April 21, 2005 - 05:21 am: |
|
You have accidentally hooked the meter
signal wire to the oxygen sensors ground wire,
Norris there is only one wire from the sensor, what kind of sensor are you using that has more than one wire??? |
Rigga
| | Posted on Thursday, April 21, 2005 - 05:35 am: |
|
hogs...there should be two wires from your o2 sensor |
Rigga
| | Posted on Thursday, April 21, 2005 - 05:36 am: |
|
i think???? now im wondering lol |
Hogs
| | Posted on Thursday, April 21, 2005 - 05:44 am: |
|
Rigga
Mine has just the one I`m sure it grounds itself out on the header ..Unless you guys are telling me that the two wires are in the same wire housing as there is only one wire coming from it ??? |
Rigga
| | Posted on Thursday, April 21, 2005 - 06:15 am: |
|
Hogs you got me thinking now,but just off to work so no time to go check,this is gonna bug me now but thinking about it more now and you are right,as when fitting the tfi there are two connections,one to the sensor and the other to the main loom connector,so only one wire runs from the o2 sensor.... i would also then assume the sensor grounds onto the exhaust header mmmm wonder if norris uprated his o2 sensor from stock??? |
Hogs
| | Posted on Thursday, April 21, 2005 - 06:21 am: |
|
No , I don`t think he did Rigga, I`ll check my connections later as of right now its SNOWING again ... |
Black_sunshine
| | Posted on Thursday, April 21, 2005 - 06:50 am: |
|
Mike....click on the Stone Mountain H-D/Buell banner in the sponsor section and talk with Clown. Odie (who makes the pipe) has it on file as well. You can get him on the 3%Bragging Rights Club thread in Storm Fronts. |
Norrisperformance
| | Posted on Thursday, April 21, 2005 - 08:46 am: |
|
Hogs
I was reading from the troubleshooting
that came with the gauge.
I think they are saying, your wires are hooked up
wrong. Maybe the ground wire is hooked to the sensor, or something like that.
lol |
Hogs
| | Posted on Thursday, April 21, 2005 - 08:50 am: |
|
LoL Norris,.. Give this Old fart a little bit more credit in knowing how to hook up a couple of wires, It worked for a few hours and then just stays at 000 `s I`ll check it later
LoL |
Opto
| | Posted on Thursday, April 21, 2005 - 01:06 pm: |
|
If it's reading all 000's then it's got power, proly the wire to the 02 sensor has become disconnected, your ecm would still be connected to the 02 sensor or you'd have a red light on the instrument panel. |
|
