Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jc1125r
| Posted on Saturday, March 05, 2016 - 06:03 am: |
|
I am wanting to make sure that I can completely remove the Harley Davidson "Fix" for the stator overheating. It has been disconnected from the stator to the Voltage Regulator, but I believe it still has two small gauge wires connected to it. Can I simply disconnect those wires and remove the entire HD fix? (HD Fix being the bundle of wires and relay that HD put between the stator & the VR) I am wanting to also use the connectors to wire in my new VR. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dannybuell
| Posted on Saturday, March 05, 2016 - 09:57 am: |
|
A fellow member... https://www.youtube.com/watch?v=nBYEYGJfyBw&featur e=youtu.be |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jc1125r
| Posted on Saturday, March 05, 2016 - 03:55 pm: |
|
Thanks, but the video does not address whether or not I can completely remove it. There are 3 other connections (see yellow arrows in photo). What are those for and can they be disconnected
![HD fix](http://www.badweatherbikers.com/buell/messages/290431/780503.jpg)
|
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Dannybuell
| Posted on Saturday, March 05, 2016 - 06:25 pm: |
|
I may be wrong, I just did the connectors. I would assume that those two may mate also? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Sparky
| Posted on Saturday, March 05, 2016 - 07:08 pm: |
|
Service Bulletin B-099 describes everything one needs to understand the "H-D Fix". Look for it in the Service Bulletins section of BadWeb. The 2 pin connector that goes to the ECM and was mated to the connector that went to the relay can be disconnected and stowed in the harness. The other 2 pin connectors that go to the Active Intake device can be mated after disconnecting from the Harley Fix harness. |
|