Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jelomadnes
| Posted on Sunday, September 11, 2011 - 03:19 pm: |
|
Between these two parts: CO152.02A8 and YO724-02A8. The later supersedes the first. My bike dies when the forks hit the locks when turned to the right. I know this is a known issue, broken solder connections at the ignition switch. I was wondering if anyone knew if the new part has a longer cable and better made connections. It's almost a $100 difference in price between the new and old parts. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Boogiman1981
| Posted on Monday, September 12, 2011 - 11:13 am: |
|
so far most folks just repair the switch and do a better job of securing the wiring than was done in east troy. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Bueller_bjorn
| Posted on Monday, September 12, 2011 - 01:41 pm: |
|
I ended up buying C0152.1AD to replace mine but found out the cable was way too short so I extended the wires myself by splicing and soldering the old wires from the busted one. so I do know that C0152.1AD part is too short to be used unless you go my route. I would also like to know the correct one that is long enough for the R's. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Froggy
| Posted on Monday, September 12, 2011 - 01:59 pm: |
|
C0152.1AD is the Lightning/1125CR part, the .02A8 part is for Firebolts and 1125R so it has the longer cable, I can't remember if the mounting bracket is the same or not for both. As for the original question, I'm not sure the difference between the two parts listed. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jelomadnes
| Posted on Tuesday, September 13, 2011 - 09:16 pm: |
|
Thanks for the info, I think I'm gonna just rebuild/solder it myself rather than buying the new part. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Jelomadnes
| Posted on Saturday, September 24, 2011 - 10:43 pm: |
|
Ok, just got back from my vacation, and started on this little project. I have got everything pretty much apart right now. Before I go any further I want to know which end of the cable I should be looking at, where it goes into the main harness or at the ignition switch. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Avalaugh
| Posted on Sunday, September 25, 2011 - 03:58 am: |
|
Switch end, also modify the bracket. Sorry only pictures i have
![](http://i66.photobucket.com/albums/h264/avalaugh/e67719ee.jpg) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Zac4mac
| Posted on Sunday, September 25, 2011 - 03:01 pm: |
|
![](http://www.badweatherbikers.com/buell/messages/290431/653022.jpg)
![](http://www.badweatherbikers.com/buell/messages/290431/653023.jpg)
![](http://www.badweatherbikers.com/buell/messages/290431/653024.jpg)
![](http://www.badweatherbikers.com/buell/messages/290431/653025.jpg) H-D combined two parts that were available separately into one, expensive switch assembly. Much better to fix the switch and mod the fairing stays so it doesn't happen again. Zack |
|