Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Georgehitch17
| Posted on Wednesday, April 06, 2011 - 11:22 am: |
|
http://www.mandrel-bends.com/catalog/collectors-x- pipes-t-s-100/x-pipes-183/parallel-x-pipes-179/x-p ipe-parallel-1-75-inlets-parallel-1-75-outlets-304 ss-1795.html |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Beugs
| Posted on Wednesday, April 06, 2011 - 12:15 pm: |
|
I've bought stuff from there, super prices and very high quality. I got a stainless u-bend to make my exhaust tips with. You can hardly even see where they bent it. Hand polished them and they look absolutely amazing. I highly recommend them. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Vinb
| Posted on Wednesday, April 06, 2011 - 12:20 pm: |
|
This is a good one too. http://www.burnsstainless.com/tubingmain.aspx |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Zac4mac
| Posted on Wednesday, April 06, 2011 - 12:20 pm: |
|
Nice tip George. They also have SS T-bolt clamps cheaper than I've seen elsewhere. Got them bookmarked now. Z |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Beugs
| Posted on Wednesday, April 06, 2011 - 01:12 pm: |
|
I looked into burns as well, same part was over twice the price. They seem to have a good selection but their prices are just too high. I compared a lot of different stainless places before I went with mandrel-bends.com, they blew everyone else out of the water. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Vinb
| Posted on Wednesday, April 06, 2011 - 03:47 pm: |
|
Burns may be more money but they have the right size pipe |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Stirz007
| Posted on Wednesday, April 06, 2011 - 05:01 pm: |
|
+1 on Burns - good selection, good quality and good service. A little more than someone else for sure, but for a set of exhaust pipes the difference is not that much. (That is, if you are efficient and don't waste much) - I always build the mock-up with carbon steel bends first, then fab the final in stainless. (Message edited by Stirz007 on April 06, 2011) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Mountainstorm
| Posted on Wednesday, April 06, 2011 - 06:57 pm: |
|
This thread makes me want to know how to weld. |
|