| Author | Message | ||
     Buellish |
All parts sold plus shipping. S2 stock muffler.Could use a repaint or run it as is.painted with high temp paint a couple of years ago.$50     Three left front/right rear S2 turn signals.One is in decent shape but has some scuffing,one has a wear mark on the bottom and one the mount has a bevel.Also one right front/left rear lens not pictured that I'll through in.$25     Various belt and pully guards,I think S1 and X1.$5 ea.      Used 27 tooth pully kit in good condition,very hard to find.$75    Starter off a '99 X1 $50  Tuber axles both complete with washers,nut and spacer,one is '97 and earlier,one '99 and later.$30 ea.  Front engine mount pre breadbox $20,upper engine mount $15,three tie bars $15  Shift lever w/linkage off I believe a '97 S1 $35  Master cylinder,reservior and line,I can't remember if it came off a '97 S1 or a '99 X1 $25  Nissin rear caliper $20  Coil off a '99 X1 $25  Side stand measures approximately 13.5" end to end at the rear $25  | ||
| S1w222 |
I'll take the 97 S1 shifter PM Sent | ||
| Buellish |
Anyone interested in parts be aware that if you don't hear from me I haven't had a lot of luck with my pm replies getting through.Also I need your zip to calculate shipping and if you just pm me your email it might work better.And please send your paypal payment as a gift. Thanks, Mike (Message edited by buellish on November 05, 2015) (Message edited by buellish on November 05, 2015) | ||
| S1w222 |
email Samadams222@gmail.com. Thx | ||
| S1w222 |
33316 | ||
| Buellish |
The S2 muffler,front engine mount and tie bars may be sold pending a shipping quote. | ||
| Kgrules |
Do you know if the brake reservoir cap will fit a 96 S2? I lost mine and would buy the setup for $25 if it fit. | ||
| Steeleagle |
Dibs on the turn signals. PM on its way. | ||
| Buellish |
"Do you know if the brake reservoir cap will fit a 96 S2" I'm pretty sure it won't and not having an S2 handy,I can't compare. | ||
| 1313 |
Short answer, it won't. | ||
| Kmbuell |
Pm sent on old style lower belt guard and shifter. Thanks, Kevin | ||
| Buellish |
Kevin,there's two people ahead of you on the shifter.Send me your email address. | ||
| S1w222 |
Passing on the shifter, thx anyway | ||
| Buellish |
Lower belt guard in the picture just before the 27T pully is sold. | ||
| Buellish |
I have a set of the original pegs for '98 and earlier tubers is you are doing a restoration these look pretty good.Set of four $25  | ||
| Buellish |
The turn signals are sold. | ||
| Hybridmomentspass |
Has the shifter sold? If it has not, please PM me thanks | ||
| Buellish |
I'm waiting on payment for the shifter from a member outside the states in a different time zone. | ||
| Kmbuell |
Mike, still interested in the shifter if it gets passed on. Thanks, Kevin | ||
| Buellish |
The shifter is sold. | ||
| Bonneville |
I may be interested in the axles, not sure which would be best. I'm looking for a set to fit '98 S1 forks. Which set will fit ? PM on its way. | ||
| Buellish |
I guess I should clarify,the axles I have are rear axles. | ||
| Bonneville |
Okay, thanks for that. | ||
| Buellish |
Still many parts left. | ||
| Steeleagle |
Got the lights in good shape. Thanks!! Bump for you as well. | ||
| Kmbuell |
Michael, Got the lower belt guard. Perfect! Thank you! Kevin | ||
| Johnod |
PM sent. Interested in upper engine mount and pegs. (Message edited by johnod on December 15, 2015) | ||
| Buellish |
Replied to. | ||
| Buellish |
The footpegs and upper engine mount are sold. |
