Author |
Message |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Knickers
| Posted on Saturday, August 21, 2010 - 03:22 pm: |
|
20 & 21 tooth drive sprockets for 520 chain. Minimal usage. $20 each or $35 for both.
![sprockets](http://www.badweatherbikers.com/buell/messages/21/588677.jpg) Brake rotor, spacer & fasteners for older level chain conversion swingarm as seen here...
![swing](http://www.badweatherbikers.com/buell/messages/21/588678.jpg) Plus wheel spacers (edges are dinged up from being pounded out of bearings but they will clean up fine). $60 for the set. Just add the sprocket spacer from Erik Buell Racing and you have a setup for a spare rear wheel.
![rotor](http://www.badweatherbikers.com/buell/messages/21/588679.jpg) Shift lever, brake lever (scraped), clutch lever. $15 each
![levers](http://www.badweatherbikers.com/buell/messages/21/588680.jpg) Set of XB-S pegs. Brand new, never used. $20
![pegs](http://www.badweatherbikers.com/buell/messages/21/588681.jpg) (Message edited by knickers on August 22, 2010) |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
72rs
| Posted on Saturday, August 21, 2010 - 03:55 pm: |
|
what would the shipping be on the pegs? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Nillaice
| Posted on Saturday, August 21, 2010 - 08:48 pm: |
|
next in line on the pegs |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Flatheadbill
| Posted on Sunday, August 22, 2010 - 08:06 am: |
|
Hi. Will these sprockets fit a tube frame (2000 X1) Buell? |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Knickers
| Posted on Sunday, August 22, 2010 - 10:39 am: |
|
I don't know. Someone in the Old School forum might know if the XB and tuber share the same transmission output spline. |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
72rs
| Posted on Sunday, August 22, 2010 - 11:22 am: |
|
payment sent for the pegs |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Knickers
| Posted on Sunday, August 22, 2010 - 11:46 am: |
|
Pegs are sold |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Lucas70374
| Posted on Sunday, August 22, 2010 - 08:00 pm: |
|
pm sent on Brake rotor, spacer & fasteners for older level chain conversion swingarm as seen here... |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Skinstains
| Posted on Sunday, August 22, 2010 - 10:50 pm: |
|
PM sent on rotor and spacers... |
![Top of page](http://www.badweatherbikers.com/buell/icons/mark_top.gif) ![Previous message](http://www.badweatherbikers.com/buell/icons/mark_up.gif) ![Next message](http://www.badweatherbikers.com/buell/icons/mark_down.gif) ![Link to this message](http://www.badweatherbikers.com/buell/icons/link-up.gif)
Knickers
| Posted on Tuesday, August 24, 2010 - 11:41 am: |
|
Rotor and spacers are sold. |
|